大盛防颱捲門 – 景衛門

DahSheng Typhoon-Resistant Rolling Door – JING WEI DOOR

17級防颱節能捲門

Grade 17 Typhoon-Resistant & Energy-Efficient Rolling Door

景衛門1 1

防颱景衛門獲得 德國 IF 設計獎

      東元捲門的專注研發,經銷商們的用心施工維護,

      我們共同創造了這一榮譽!恭禧!恭禧!

JING WEI DOOR Wins Germany’s iF Design Award!
Thanks to TECO’s innovation and our dealers’ dedication — this honor belongs to all of us. Congratulations!

IF設計獎

高雅透氣 Elegant and Breathable

採用雙層平面鋁合金門片,中間穿插格線條凸顯整體高雅大方,並能隨意調整門片上透氣孔,流通新鮮空氣促進身心健康。

Featuring double-layer flat aluminum alloy doors with interwoven grid lines that highlight an overall sense of elegance and simplicity. The ventilation holes on the doors can be freely adjusted to allow fresh air to circulate, promoting physical and mental well-being.

強化結構 Reinforced Structure

門片材料腔型中空設計,提高外 力施壓的結構強度與韌性。

The door panels feature a hollow chamber design, enhancing structural strength and resilience against external pressure.

高抗風能力 High Wind Resistance

雙弧型卡勾連結加強筋專利導軌與防颱勾搭配,捲門寬度7米時能承受17級強烈颱風。

 The patented dual-arc hook connection, reinforced track, and typhoon-resistant latch work together to ensure the rolling door can withstand a Category 17 typhoon, even at a width of 7 meters.

 

.

抗風壓結構性能試驗

正風壓 壓力=5000Pa(500kgf/m2)

1.加壓過程中,無損壞現象

2.除壓後,無妨礙機能之殘流變形


Wind Pressure Resistance Structural Performance Test
Positive Wind Pressure: Pressure = 5000 Pa (500 kgf/m²)

1. No damage observed during the pressurization process

2. No residual deformation affecting functionality after pressure release

景衛羅拉 景衛門捲箱尺寸
2024.11.25 東元捲門目錄 03 04 03
05 01 1
景衛羅拉 景衛門捲箱尺寸 複本

             總高超過6米捲箱尺寸,請洽總公司

              For rolling doors with a total height exceeding 6 meters, please contact our head office for details
4981143 02

大盛防颱捲門 – 景衛門

實績產品分享 Product Case Studies

02 1 scaled
5 scaled

大盛防颱景衛捲門實例

Jingwei Rolling Door – Real Case Application
333 scaled
01 scaled

大盛防颱景衛捲門實例

Jingwei Rolling Door – Real Case Application
03 1 scaled
抗17及颱風 scaled

大盛防颱景衛捲門實例

Jingwei Rolling Door – Real Case Application
4981143 02

大盛防颱捲門 – 施工圖說 Construction Documents

01 1

W 總寬

 Overall Width

H 總高

Overall Height

h 淨高

Net Height

D 捲箱深度 

Roller Box Depth

B 捲箱高度

Roller Box Height

01
03
06
07

施工規範 Installation Specifications

1.施工前應確認以下事項: 材料 / 尺寸 / 電源位置 / 電壓,如圖紙要求,且無管道干涉;如不符合要求,應與現場主管反應,待確認後再進行工程施作。

1. BEFORE CONSTRUCTION, THE FOLLOWING ITEMS MUST BE CONFIRMED:MATERIALS / DIMENSIONS / POWER SOURCE LOCATION / VOLTAGE, AS SPECIFIED IN THE DRAWINGS, AND ENSURE THERE ARE NO PIPELINE INTERFERENCES.IF ANY CONDITIONS DO NOT MEET THE REQUIREMENTS, NOTIFY THE SITE SUPERVISOR AND PROCEED WITH THE WORK ONLY AFTER RECEIVING CONFIRMATION.

2.因應現場變更修改材料尺寸時,需確認裁切沒有導致電路損傷狀況。

2. WHEN MODIFYING MATERIAL DIMENSIONS DUE TO ON-SITE CHANGES, ENSURE THAT CUTTING DOES NOT RESULT IN DAMAGE TO THE ELECTRICAL WIRING.

3.捲箱、導軌的水平度和垂直度於公差範圍內,導軌平行度公差應小於3mm。

THE ROLLER BOX AND GUIDE RAILS MUST BE LEVEL AND VERTICAL WITHIN TOLERANCE, WITH THE GUIDE RAILS’ PARALLELISM TOLERANCE LESS THAN 3 MM.

4.使用Φ12mm x 90 mm 或以上的不銹鋼膨脹螺絲固定,固定方式應按圖說施作,間距不大於15cm。

4. Use stainless steel expansion bolts of Φ12mm × 90mm or larger for fixing. Installation should follow the construction drawings, with spacing not exceeding 15 cm.

5.電線配置應明確標示,避免電線與捲動部位接觸的風險。

5. ELECTRICAL WIRING LAYOUT MUST BE CLEARLY INDICATED TO AVOID ANY RISK OF CONTACT BETWEEN WIRES AND MOVING PARTS.

6.功能安全測試,確保捲門安全順暢運行:

(1)底支障礙碰停開關動作方向是否正確,必須反應靈敏。

(2)紅外線安全防護裝置動作確認。

(3)確認控制系統操作靈敏,運行無異常噪音。

(4)捲門啟閉應順暢自如,電動至上下定點能自動停止。

6. Functional Safety Test – Ensure safe and smooth roller shutter operation:
(1) Check bottom limit switch response and direction; must be accurate and sensitive.
(2) Confirm infrared safety sensor is functioning properly.
(3) Ensure control system responds smoothly with no abnormal noise.
(4) Shutter should open/close smoothly and stop automatically at top and bottom limits.

7.確認產品標牌標示是否正確、清楚,應記錄出廠日期。

7. VERIFY THAT THE PRODUCT LABEL IS CORRECT AND CLEAR, AND RECORD THE MANUFACTURING DATE.

8.馬達應有溫度保護裝置,馬達過熱時即自動切斷電源。

8. THE MOTOR SHOULD HAVE A TEMPERATURE PROTECTION DEVICE THAT AUTOMATICALLY CUTS OFF THE POWER WHEN OVERHEATING.

9.製造商應有IS09001品保認證,並提供證明書。

9. THE MANUFACTURER SHOULD HAVE ISO 9001 QUALITY CERTIFICATION AND PROVIDE THE CERTIFICATE.
4981143 02

外掛式 Plug-in type / 複合式 Hybrid type

實績產品分享 Project Portfolio Sharing

01
02 1

Copyright © 2025東元捲門事業股份有限公司. All rights reserved.